Engine (2)

-€10.86

ANDREWS Camshaft Drive Gear — 2.7670" diameter, P/N 212044

Precision camshaft drive gear engineered for reliable valve timing. Made in the U.S.A.; measured with .105 gauge pins.

€42.24 €53.10

-€10.60

ANDREWS Cam Drive Gear — Standard, 2.7354" diameter

High-quality heat-treated cam drive gear. Made in the U.S.A. Direct-fit replacement.

€41.20 €51.80

-€83.75

ANDREWS Cam Set for Chain Drive — 9 Series

Bolt-in cam set improving power from 1000–5400 rpm. Made from alloy steel billets; computer-designed profile. Uses stock springs. Installer must check clearances.

€325.69 €409.44

-€83.75

ANDREWS Cam Set for Chain Drive — Grind 48H, Pair

Broad-tip cams tuned for strong low- and mid-range torque. Computer-aided design, billet alloy-steel construction, and heat-treated for durability. Made in USA.

€325.69 €409.44

-€95.59

WISECO Forged Piston Kit — 1200 cc, 12.0:1

High-performance piston kit with aerospace-grade alloys. Includes pistons, rings, pins, clips, and needle bearing when applicable. Dyno-tested for superior performance.

€270.44 €366.03

Cam Set for Chain Drive — 57 Series, Intake 236°, Exhaust 240°, Pair

-€83.75

ANDREWS Cam Set for Chain Drive — 57 Series, Intake 236°, Exhaust...

Computer-designed alloy-steel cam sets made in the USA; installer must verify clearances and splined cam drive sprocket compatibility.

€325.69 €409.44

High-Performance Replacement Ring Set — 3.875" bore, +0.010" oversize, 95" displacement

On sale!
-€6.84

WISECO High-Performance Replacement Ring Set — 3.875" bore, +0.010"...

Includes rings for one piston only.

Designed specifically for compatibility with Wiseco pistons.

€19.36 €26.20

On sale!
-€50.40

ANDREWS Cams for M-Eight — 107", 114", stock compression

Bolt-in cam for M-Eight 107" and 114" engines; maintains stock compression and improves midrange torque.

€196.40 €246.80

-€50.40

ANDREWS Cams for M-Eight — 107 ci, 114 ci

Bolt-in cam for M-Eight engines; fits stock compression 107 ci and 114 ci.

€196.40 €246.80

On sale!
-€50.40

ANDREWS Cams for M-Eight — Exhaust 236°/0.504", Intake 216°/0.105"

Bolt-in cam for stock-compression 107" and 114" M-Eight engines. Direct-fit upgrade to improve midrange performance and throttle response.

€196.40 €246.80

-€13.23

ANDREWS Cam Sprocket — 17T

Precision cam sprocket built for reliable valve timing and long service life.

€56.31 €69.54

-€50.40

ANDREWS M462 Cam — 220° exhaust, 200° intake, 0.460" lift

Bolt-in cam for 107"–114" engines. 127 ft lb torque, 109 hp from 1200–5500 rpm. Designed for strong midrange power and direct bolt-in fitment.

€196.40 €246.80

M464 Cam — Exhaust duration 230°, Intake duration 210°, Exhaust lift 0.460", Intake lift 0.464"

-€50.40

ANDREWS M464 Cam — Exhaust duration 230°, Intake duration 210°,...

Great mid-range torque and power with free-flow exhaust pipes and injector tuning.

€196.40 €246.80

554 Cam — 554 series grind, for 124"/128" big-bore motors, chrome

-€50.40

ANDREWS 554 Cam — 554 series grind, for 124"/128" big-bore motors, chrome

Fits 124" and 128" big-bore motors with head work. Made in the U.S.A. Requires hi-lift springs.

€196.40 €246.80

-€50.40

ANDREWS Camshaft — M520, Exhaust 248°, Intake 228°, Lift 0.520"

Precision-engineered camshaft, made in the U.S.A., for durable, smooth power delivery.

€196.40 €246.80

-€50.40

ANDREWS 465B Cam — Bolt-in

Bolt-in chain drive cam for 107–117" engines. Works with stock valve springs. Excellent low to mid rpm torque (1200–5600 rpm).

€196.40 €246.80

485 Bolt-In Cam — 0.485" lift, fits 107 cu in+ engines

-€50.40

ANDREWS 485 Bolt-In Cam — 0.485" lift, fits 107 cu in+ engines

Highest-lift bolt-in chain drive cam compatible with stock valve springs; strong low- to mid-range power for 107 cu in and larger engines.

€196.40 €246.80

-€62.36

ANDREWS EZ-Install Pushrods — 4-pack, aluminum

Eliminate the need to disassemble rocker boxes or remove the gas tank for cam changes and routine maintenance. Made in the U.S.A.

€242.55 €304.91

-€59.16

ANDREWS EZ-Install Pushrods — 4 Pack, Chromoly

EZ-install pushrods that eliminate removing rocker boxes or the gas tank during cam changes. Made in the U.S.A.

€230.08 €289.24

-€101.56

ANDREWS N2 Grind Cams — Gear, 4 Pack

Proven N2 cam profile; runs to 6500 rpm with stock hydraulic lifters. Made in the U.S.A.

€394.98 €496.54

-€101.56

ANDREWS N4 Grind Cams — 256° duration, 0.490 in lift

Balanced street-oriented cam profile; revs to 6,500 rpm on stock hydraulic lifters. Made in the U.S.A.; solids not recommended.

€394.98 €496.54

-€50.75

ANDREWS EV23 Cam — EV23 grind, Chain, Intake 220°/Exhaust 228°

Bolt-in EV23 cam for heavier touring and high-geared bikes; works with stock springs and either carbs or EFI. Strong pull from 1500–6000 rpm. Made in the USA. Check coil bind and clearances.

€197.35 €248.10

-€24.63

ANDREWS Cam Chain Drive Sprocket — 288015

Direct replacement cam drive sprocket. Replaces the stock 34-tooth unit; includes shims. Crankshaft sprocket is 17-tooth. Made in the U.S.A.

€95.81 €120.44

Cam Set for Chain Drive — 26 Series, Intake 226°, Exhaust 266°, Lift 0.490"

-€83.75

ANDREWS Cam Set for Chain Drive — 26 Series, Intake 226°, Exhaust...

Precision-machined cam set manufactured in the USA from alloy steel billets. Installer must check coil bind, valve-to-valve clearance and valve-to-piston clearance. Designed for chain drive applications.

€325.69 €409.44

-€83.75

ANDREWS Cam Set for Chain Drive — 37 Series, Intake 236°, Exhaust 240°

Precision-machined cam set for chain-drive applications. Made in the USA. Installer must verify clearances.

€325.69 €409.44

N2 Grind Cams — Intake 240°/0.465" lift, Exhaust 244°/0.440" lift, Gear

-€102.70

ANDREWS N2 Grind Cams — Intake 240°/0.465" lift, Exhaust 244°/0.440"...

N2 Grind cams for dependable street performance. Runs to 6500 rpm with stock hydraulic lifters; solids not recommended. Stock base circle sizes allow use of stock pushrods. Made in the U.S.A.

€398.82 €501.52

-€101.56

ANDREWS N4 Grind Cams — 256° duration, 0.490" lift, chain, 4-pack

Performance cam kit for use with stock hydraulic lifters. Made in the U.S.A. Stock base circle sizes retain stock pushrod compatibility.

€394.98 €496.54

J Grind Cam — Intake & exhaust, 242° duration, 0.405"/0.425" lift

-€50.69

ANDREWS J Grind Cam — Intake & exhaust, 242° duration, 0.405"/0.425" lift

Increases mid-range and top-end power for street and drag bikes; bolt-in, works with solid or hydraulic lifters, maintains a smooth idle.

€197.15 €247.84

J Grind Cam — 242° duration, 0.405" lift

-€50.69

ANDREWS J Grind Cam — 242° duration, 0.405" lift

Increases mid-range and top-end power for street and drag bikes. Works with solid or hydraulic lifters. Bolt-in installation; verify coil bind and clearances. Made in USA.

€197.15 €247.84

-€50.69

ANDREWS J Grind Cam — 242° duration, 0.405" lift

More mid-range and top-end power for street and drag bikes; bolt-in with no head work; works with solid or hydraulic lifters; made in USA.

€197.15 €247.84

shop by category

Engine

Subcategories

Complete Engines

Performance Kits

Internal Parts

Cooling

Gaskets & O-Rings

Camshafts

Contact us

Products

Our company

shop by category

Engine  

Subcategories

Complete Engines

Performance Kits

Internal Parts

Cooling

Gaskets & O-Rings

Camshafts

Engine