VTwin & Specific Tools

Pinion Gear Locker Tool — pinion gear, Black

-€16.21

JIMS Pinion Gear Locker Tool — pinion gear, Black

Locks the gear while torquing the nut; aligns under the gear and screws into the case. Made in the U.S.A.

€63.02 €79.23

Sprocket Lock Tool — Crankshaft, camshaft, Black

-€23.73

JIMS Sprocket Lock Tool — Crankshaft, camshaft, Black

Locks camshafts and crankshaft sprockets for safe removal, replacement and torquing. Includes instructions. Made in the U.S.A.

€92.27 €116.00

-€84.43

JIMS Inner Cam Bearing Removal Tool — Kit, Black

Purpose-built tool for removing inner cam bearings without damaging the crankcase; includes instructions and retention design to prevent rollers from falling into the engine.

€328.33 €412.76

-€99.44

JIMS Case Splitter Tool — Crankcase, Black

Separates sealed engine case halves using a hand thread-in pushing screw; bolts to primary mounting holes. Made in the U.S.A.

€386.69 €486.13

-€27.02

JIMS Valve Spring Compressor — Valve Spring, Gray

Removes and replaces valves and new-style conical valve springs. Requires the dedicated valve spring compressor tool. Made in the U.S.A.

€105.09 €132.11

-€43.41

JIMS Driver Handle — 6-Speed, Blue anodized

Tool for installing the main drive gear oil seal with a protective sleeve; made in the U.S.A.

€168.77 €212.18

25 mm Wheel Bearing Adapter — 25 mm, 2007–2019 Harley-Davidson fit, Black

-€21.10

JIMS 25 mm Wheel Bearing Adapter — 25 mm, 2007–2019 Harley-Davidson...

Made in the USA. For use with 25 mm wheel bearings on 2007–2019 Harley-Davidson® models. Precision-machined adapter for safe bearing removal.

€82.06 €103.16

-€42.16

JIMS 49mm Fork Seal and Dust Shield Installer — Blue

Installs lower leg 49 mm fork seals squarely without damaging the seal lip. Two-piece design for easier assembly and dust shield cover installation. Made in the U.S.A.

€163.95 €206.11

Cylinder Torque Plate Kit — 3.75"–3.875" bore, black

-€158.86

JIMS Cylinder Torque Plate Kit — 3.75"–3.875" bore, black

Use these plates when boring or honing late-model aluminum cylinders to simulate running stress conditions. Includes instructions. Made in the U.S.A.

€617.77 €776.63

-€21.59

JIMS Pushrod Cover Clip — Pushrod, Black

Quick one-hand tool for installing and removing cover clips. Won't mar or slip. Made in the U.S.A.

€83.97 €105.56

Piston Ring Compressor Set — 47.6 mm–73 mm (1-7/8"–2-7/8"), Set of 4, Black

-€34.82

JIMS Piston Ring Compressor Set — 47.6 mm–73 mm (1-7/8"–2-7/8"),...

Precise ratcheting compressor that compresses piston rings in small increments without damaging them. Made in the U.S.A.

€135.41 €170.23

-€44.20

JIMS Dual Gauge Leakdown Tester — JIMS, Cylinder, 4-Stroke, Black

Dual-gauge design for quick leakdown diagnosis; detects valve-seat leaks, bad rings and head gasket failures.

€171.90 €216.10

-€10.56

JIMS Hydraulic Balancer Retainer Tool — Engine balancer, Silver

Holds hydraulic tensioners to maintain constant chain tension on counter balancer systems. Made in the U.S.A.

€41.03 €51.59

-€48.97

JIMS Mini Valve Spring Tester — Black, Blue

Compact tester for dual-rate and conical valve springs; fits up to 1.6" O.D.; 0–1000 P.S.I. gauge. Made in the U.S.A.

€190.44 €239.41

-€9.19

JIMS Dipstick Removal Tool — Engine oil system, Gray

Safely removes engine oil dipsticks near hot exhausts; fits 3/8" ratchet and 7/8" wrench. Made in the U.S.A.

€35.75 €44.94

-€13.08

JIMS Mighty Bite Flywheel Lock and Tag — Blue

Secures the flywheel for service on Twin Cam motors; installs in place of the crank position sensor and includes a visible decommissioned tag.

€50.85 €63.93

$Piston Ring End Gap Tool — Fits H-D 95\", 103\", 110\" motors, 3.875\" or 4\" bore, blue anodized$

-€22.66

JIMS Piston Ring End Gap Tool — Fits H-D 95\", 103\", 110\" motors,...

Measures piston ring end gap quickly and accurately. Flanged design ensures a square fit in the bore. Fits H-D 95\", 103\", 110\" motors with 3.875\" or 4\" bore.

€88.13 €110.79

Tappet Position Holding Tool — Camshaft, Tappet, Black, Blue, Silver

-€19.21

JIMS Tappet Position Holding Tool — Camshaft, Tappet, Black, Blue,...

Protects and organizes tappets during camshaft service; stores pins and tappets for accurate reinstallation. Made in the U.S.A.

€74.70 €93.91

-€22.46

JIMS Wrist Pin Adapter — wrist pin, gray

Removes wrist pins from Milwaukee-Eight® engines
Accessory for JIMS® Wrist Pin Tool (DS-196197)
Made in the U.S.A.

€87.34 €109.80

-€84.85

JIMS Milwaukee-Eight® Cam Bearing Tool — Black

Precision tool for camshaft inner needle bearing installation with tighter tolerances for accurate depth. Proven remover collet and fine-threaded installation driver. Made in the U.S.A.

€329.98 €414.83

-€20.62

JIMS Valve Spring Collar — Adapter, Black, Part 5808

Allows an existing compressor to remove smaller valves on M8 engines. For use with JIMS® Valve Spring Compressor Tool (PART# DS-196013). Made in the U.S.A.

€80.18 €100.80

-€22.64

JIMS Cylinder Hold Down Nuts — Blue, fits Twin Cam and Milwaukee Eight

Hold-down nuts for securing the cylinder during head removal; one end fits Twin Cam, the other fits Milwaukee Eight. Made in the U.S.A.

€88.03 €110.67

-€26.42

JIMS Main Seal Installer/Remover — JIMS, Part No. 5810

Tool for installing and removing the main crankshaft seal on Milwaukee Eight engines.

€102.75 €129.17

-€213.23

JIMS Cylinder Torque Plate Kit — 3.937"–4" bore, black

Required when boring or honing late-model aluminum cylinders; simulates running stress; includes instructions; made in the U.S.A.

€829.24 €1,042.47

Engine Stand — fits Milwaukee‑Eight Softail engines, 7 gauge (0.1875") steel, powder-coated blue

-€33.63

JIMS Engine Stand — fits Milwaukee‑Eight Softail engines, 7 gauge...

Securely mounts Milwaukee‑Eight Softail engines; fabricated from 7 gauge (0.1875") powder-coated steel for durable use.

€130.80 €164.43

-€14.56

JIMS Socket Dipstick Insert Tool — 760K, Blue, Black, Kit

Easy-install insert for safe dipstick cap removal; lifetime-guaranteed design by Gary Smith; option available with a compatible socket for older bikes.

€56.61 €71.17

-€17.48

JIMS Oil Pump Alignment Tool — Black

Designed to help technicians assemble the complete cam chest quickly and accurately. Use with supplied studs or as an assembly with the alignment dowel. Made in the U.S.A.

€67.95 €85.43

-€15.25

JIMS Magnetic Tappet Holder — Pushrod application

Holds the tappet securely for preliminary adjustment and prevents engine rotation while pushrods are tight. Verify tappet spins freely before turning the engine.

€59.28 €74.53

-€68.09

JIMS Piston Jet Tester — Blue, PN 730

Clears assembly lubes and verifies jet psi and spray pattern before sealing; does not include piston jet.

€264.80 €332.89

Milwaukee Eight® Stator Adapter Main Bearing Tool — Stator, Black Oxide

-€10.00

JIMS Milwaukee Eight® Stator Adapter Main Bearing Tool — Stator,...

Keeps the stator attached to the left side case during main bearing installation for faster, cleaner service.

€38.95 €48.95

shop by category

VTwin & Specific Tools

VTwin & Specific Tools

Subcategories

Engine Tools

Contact us

Products

Our company

shop by category

VTwin & Specific Tools  

VTwin & Specific Tools

Subcategories

Engine Tools

VTwin & Specific Tools