VTwin & Specific Tools

-€25.68

KIBBLEWHITE Valve Guide Reamer — 181 mm (7.125"), Nickel

Precision reamer for valve guides designed for KPMI® manganese bronze and cast iron.

Do not use a reamer on bronze after it has been used on cast iron.

€72.64 €98.32

-€2.37

DRAG SPECIALTIES Oil Filter Wrench — 14-flute, Black

Compact oil filter wrench with cutout profile for crank sensor clearance; fits most common filters.

€6.72 €9.09

Tappet Screen Plug Tool — for big twin (excl. twin cam), slotted screw tappet screen cover, black

-€2.81

MOTION PRO Tappet Screen Plug Tool — for big twin (excl. twin cam),...

Removes and installs tappet oil filter screen plugs for big twin models (excl. twin cam); fits a 7/16" combination wrench.

€7.95 €10.76

Belt Tension Gauge — 10 lb spec, Black, Silver

-€7.39

MOTION PRO Belt Tension Gauge — 10 lb spec, Black, Silver

Compact belt tension gauge with graduated scale and L-shaped pad; measures to a 10 lb specification.

€20.89 €28.28

Pinion Gear Locker Tool — pinion gear, Black

-€16.21

JIMS Pinion Gear Locker Tool — pinion gear, Black

Locks the gear while torquing the nut; aligns under the gear and screws into the case. Made in the U.S.A.

€63.02 €79.23

Flywheel Puller Right Hand Internal Thread — M35 x 1.5, black oxide

-€10.35

MOTION PRO Flywheel Puller Right Hand Internal Thread — M35 x 1.5, black...

Precision right-hand internal thread puller for safe removal of flywheels or rotors. Heat treated, durable finish, lifetime limited warranty.

€29.25 €39.60

-€5.03

MOTION PRO Rocker Box Wrench — Rocker Box Cover, Black

Designed to reach 3/16" hex screws on the rocker boxes of Big Twin, Sportster and Buell models. Vinyl-covered area reduces the chance of surface damage. 3/8" drive for torque-tool use.

€14.20 €19.23

Adapter for Air-Cooled Engine — 19 mm OD, 55 mm length, 2-stroke, Silver

-€4.14

MOTION PRO Adapter for Air-Cooled Engine — 19 mm OD, 55 mm length,...

Enables use of water-cooled 2-stroke timing kits on air-cooled engines with 14 mm spark plugs. Includes extended thread adapter and dial indicator extension. Not compatible with Yamaha RD two-stroke twins while engine is in frame.

€11.69 €15.83

-€47.64

MOTION PRO Timing Kit — Water Cooled, 2-Stroke, Silver

Dial indicator set with extensions and a 14 mm spark plug thread adapter; 1-1/2" gauge face for accurate timing checks.

€134.61 €182.25

-€24.54

MOTION PRO Wheel Bearing Remover Set — 8-piece, 10–25 mm, metric, black

Eight-piece bearing remover kit with large and small driver rods and removers for 10–25 mm bearings. Dependable split collet design and heat treated for longevity.

€69.38 €93.92

-€3.19

SHOW CHROME Oil Filter Wrench — Thin, Silver

Removes the oil filter without removing fairing pieces; secure locking mechanism requires no adjustment; fits most 2-1/2" filters.

€13.30 €16.49

-€25.43

K&L SUPPLY 6-in-1 Flywheel Puller — K&L SUPPLY, Steel, Metric

Compact 6-in-1 design with adapters for M10 x 1.25R, M14 x 1.5R, M16 x 1.5R, M18 x 1.5R, M24 x 1.0R and M27 x 1.0R.

€27.23 €52.66

Dual Drive T-Handle Set — 4, 5, 6, 8 mm hex, 171.5 mm, Nickel pewter

-€15.63

MOTION PRO Dual Drive T-Handle Set — 4, 5, 6, 8 mm hex, 171.5 mm, Nickel...

Four-piece T-handle hex set with ball-end for angled access up to 25°; ideal for shaft-mounted fasteners and tight spaces.

€44.18 €59.81

Dual-Drive Allen T-Handle — 5 mm, 171.5 mm (6-3/4"), Nickel Pewter

-€3.70

MOTION PRO Dual-Drive Allen T-Handle — 5 mm, 171.5 mm (6-3/4"), Nickel...

T-handle hex for quick tightening and loosening; ball end reaches Allen-head bolts up to 25°.

€10.43 €14.13

-€3.41

MOTION PRO Dual-Drive Allen T-Handle — 6 mm, 171.5 mm

T-handle Allen key with a ball-end tip for quick installation and angled access up to 25°.

€9.60 €13.01

Sprocket Lock Tool — Crankshaft, camshaft, Black

-€23.73

JIMS Sprocket Lock Tool — Crankshaft, camshaft, Black

Locks camshafts and crankshaft sprockets for safe removal, replacement and torquing. Includes instructions. Made in the U.S.A.

€92.27 €116.00

-€84.43

JIMS Inner Cam Bearing Removal Tool — Kit, Black

Purpose-built tool for removing inner cam bearings without damaging the crankcase; includes instructions and retention design to prevent rollers from falling into the engine.

€328.33 €412.76

-€99.44

JIMS Case Splitter Tool — Crankcase, Black

Separates sealed engine case halves using a hand thread-in pushing screw; bolts to primary mounting holes. Made in the U.S.A.

€386.69 €486.13

-€27.02

JIMS Valve Spring Compressor — Valve Spring, Gray

Removes and replaces valves and new-style conical valve springs. Requires the dedicated valve spring compressor tool. Made in the U.S.A.

€105.09 €132.11

-€11.41

FEULING OIL PUMP CORP. Camplate Roll Pin Removal/Installation Tool — Red

Tool for quick removal and installation of the pressure relief spring, by-pass valve and roll pin. Holds the relief spring down and away from the roll pin. Made in the USA.

€44.40 €55.81

-€46.14

FEULING OIL PUMP CORP. Camplate Tool — PSI Relief Valve, Black, Red, Silver

Test and set cam plate relief valve pop-off psi. Includes air regulator, 0-100 psi gauge, gasket and hardware. Bench test before installation.

€179.42 €225.56

-€2.52

MOTION PRO Wheel Bearing Remover — Split collet, black

Heat treated for long life; removes wheel bearings cleanly and safely for maintenance and shop use.

€7.11 €9.63

Flywheel Puller Right Hand Internal Thread — M33 x 1.5, black oxide

-€11.83

MOTION PRO Flywheel Puller Right Hand Internal Thread — M33 x 1.5, black...

Reliable right-hand flywheel puller for safe removal of flywheels and rotors. Heat treated, durable finish, lifetime limited warranty.

€33.42 €45.25

-€2.52

MOTION PRO Float Bowl Wrench — Silver anodized

Removes 17 mm float bowl drain plugs; doubles as a high-speed compression adjuster for most Showa, KYB, and WP rear shocks. 12-point, low-profile design.

€7.11 €9.63

Seal/Bearing Retainer Tool — 47 mm lock rings, 22 mm hex, silver

-€7.75

MOTION PRO Seal/Bearing Retainer Tool — 47 mm lock rings, 22 mm hex, silver

Precision tool to remove and replace rear wheel bearing/seal retainer rings for 47 mm lock rings; features a 22 mm hex.

€21.91 €29.66

Engine Stand — For Evo Big Twin, Blue, Powder-coated

-€28.02

S&S CYCLE Engine Stand — For Evo Big Twin, Blue, Powder-coated

Professional display appearance; protects against corrosion and minor abrasions. Economical solution for bench work, shipping, or display. Made in the U.S.A.

€109.19 €137.21

-€29.35

S&S CYCLE Engine Stand — For Twin Cam A Motor, Blue

Professional-looking support that protects finishes and provides an economical way to hold an engine for workbench use, shipping, or display. Made in the U.S.A.

€114.36 €143.71

-€23.86

S&S CYCLE Engine Stand — For Twin Cam B Motor, Blue

Professional display-quality engine stand that protects against corrosion and minor abrasions. An economical solution for bench work, shipping, or display. Made in the U.S.A.

€92.77 €116.63

-€43.41

JIMS Driver Handle — 6-Speed, Blue anodized

Tool for installing the main drive gear oil seal with a protective sleeve; made in the U.S.A.

€168.77 €212.18

25 mm Wheel Bearing Adapter — 25 mm, 2007–2019 Harley-Davidson fit, Black

-€21.10

JIMS 25 mm Wheel Bearing Adapter — 25 mm, 2007–2019 Harley-Davidson...

Made in the USA. For use with 25 mm wheel bearings on 2007–2019 Harley-Davidson® models. Precision-machined adapter for safe bearing removal.

€82.06 €103.16

shop by category

VTwin & Specific Tools

VTwin & Specific Tools

Subcategories

Engine Tools

Contact us

Products

Our company

shop by category

VTwin & Specific Tools  

VTwin & Specific Tools

Subcategories

Engine Tools

VTwin & Specific Tools