VTwin & Specific Tools (7)

-€16.98

JIMS Cam Chain Tensioner Tool — Cam

Unloads pressure on primary and secondary chain tensioners for easier cam assembly and disassembly. Includes instructions. Made in the U.S.A.

€66.05 €83.03

-€134.31

JIMS Camshaft Removal/Installation Tool — Front, Rear

Multi-function tool for removing and installing front and rear camshafts and ball bearings on Twin Cam 88 engines. Made in the U.S.A.

€168.76 €303.07

Sprocket Lock Tool — Crankshaft, Camshaft, Black

-€17.78

JIMS Sprocket Lock Tool — Crankshaft, Camshaft, Black

Locks camshaft and crankshaft sprockets for safe removal, replacement, and torquing of sprocket bolts. Includes instructions. Made in the U.S.

€69.16 €86.94

-€14.29

JIMS Wrist Pin Bushing — Standard, pair

Precision bronze wrist pin bushings machined to hold concentricity to less than .0002" with a lead-in edge for easy installation.

€55.57 €69.86

-€28.57

JIMS Clutch Hub Puller — Clutch hub, Black

Works on Big Twin sprockets, alternator covers and early XL clutches. Fits 3-, 5-, 10-finger and 45" hubs. Made in the U.S.A.

€111.14 €139.71

-€26.97

JIMS Top Nut Fork Socket — 35 mm

Tool for removing and installing top fork nuts; rubber-protected socket, clears most handlebars.

€104.89 €131.86

Balancer Shaft Bearing Remover — Kit, Black

-€48.93

JIMS Balancer Shaft Bearing Remover — Kit, Black

Safe, damage-free removal of balancer shaft bearings; pushes on the bearing outer diameter; removes bearings from the "B" motor case in one smooth motion; made in the USA.

€190.26 €239.19

-€7.81

JIMS Balancer Shaft Retention Pins — Flywheel assembly, silver

Locks into balancer shaft sprocket pinholes to prevent the balancer from turning out of sync with the flywheel. Use when servicing the flywheel assembly. Made in the U.S.A.

€30.39 €38.20

-€28.78

JIMS Piston Support Plate — JIMS 1164, Black

Non-marring flat plate for pushing piston bottoms during ring or cylinder installation. Made in the U.S.A.

€111.93 €140.71

Compression Release Valve Installation Kit — Engine case fit

-€142.45

JIMS Compression Release Valve Installation Kit — Engine case fit

Complete kit to drill, spot face, tap and install compression release valves on front and rear heads; fits big-inch and high-compression Twin Cams.

€553.95 €696.40

-€14.28

S&S CYCLE Crankcase Oil Passage Drilling Jig — Crankcase oil passage, gray

Precision drilling jig for preparing oil passages; used to install S&S® oil pumps on early motor cases. Made in the U.S.A.

€55.52 €69.80

Inner Cam Bearing Go and No-Go Gauges — pair, silver

-€18.34

JIMS Inner Cam Bearing Go and No-Go Gauges — pair, silver

Fast, accurate Go/No‑Go gauges to check the inside diameter of inner cam bearings. Use them to confirm whether the cam will be too loose or too tight. Made in the U.S.A.

€71.39 €89.73

-€26.87

JIMS Fork Seal and Cap Installer — 41 mm fork tube, black

Installs fork and dust seals; lightly grease before use. Made in the U.S.A.

€104.50 €131.37

Exhaust Stud Drill Plate — Blue, anodized

-€40.00

JIMS Exhaust Stud Drill Plate — Blue, anodized

Positions exhaust port seals evenly and works with exhaust flange nuts. Made in the U.S.A.

€155.56 €195.56

Head Bolt Torque Gauge — Torque plate, head bolt application, blue

-€6.19

JIMS Head Bolt Torque Gauge — Torque plate, head bolt application,...

Accurate gauge for measuring 90° when tightening head bolts. Laser-engraved torquing sequence; fits Twin Cam and Evolution engines; made in the U.S.A.

€24.07 €30.26

-€52.24

JIMS Inner Cam Bearing Installation Tool — Right, Black

Presses inner cam bearings to the correct depth for accurate seating. Made in the U.S.A.

€203.16 €255.40

-€22.12

JIMS Clutch Spring Compressor Nut — Black

Tool for releasing the clutch spring; enables easy retainer ring removal and installation. Made in the USA.

€62.53 €84.65

-€33.12

JIMS Snap Ring Tool — Timken® bearing, black

Tool for removing and installing outer race snap rings on tapered roller bearings. Essential for OEM and aftermarket case ring replacements. Made in the U.S.A.

€128.78 €161.90

Tappet Block Alignment Tool — Crankcase, Black

-€7.15

JIMS Tappet Block Alignment Tool — Crankcase, Black

Precision tool for aligning the crankcase oil hole to the tappet block; also used for Evolution head rocker box bases and Harley-Davidson® Twin Cam oil pump alignment. Made in the U.S.A.

€27.78 €34.93

Transmission Shaft Installer — 5-Speed, Black

-€30.16

JIMS Transmission Shaft Installer — 5-Speed, Black

Installs shafts without the use of a hydraulic or arbor press. Made in the U.S.A.

€117.28 €147.44

-€23.66

JIMS Steering Head Bearing Race Installer — Black

Installs steering head bearing races and frame cups straight and without damage; made in the U.S.A.

€92.01 €115.67

-€87.73

JIMS Sprocket Shaft Bearing Remover — Sprocket shaft, Black

Removes Timken® bearings on late '86–'02 Big Twins; durable U.S.-made construction.

€341.16 €428.89

-€51.82

JIMS Main Drive Gear Bearing Removal Tool — 5-Speed, Blue, Silver

Removes old bearings straight without damaging the transmission case; usable without removing the transmission from the bike. Made in the U.S.A.

€201.53 €253.35

Driver Handle — Main drive gear, 5-speed, Blue anodized

-€33.92

JIMS Driver Handle — Main drive gear, 5-speed, Blue anodized

Installs main drive gear oil seal to correct depth with transmission assembled; includes protective sleeve; made in the U.S.A.

€131.92 €165.84

Tappet Oil Filter Screw Plug Tool — Black

-€10.19

JIMS Tappet Oil Filter Screw Plug Tool — Black

Removes tappet oil screen without removing the exhaust. Used to extract the tappet oil screen plug. Made in the U.S.A.

€39.65 €49.84

Shouldered Valve Guide Driver Set — 3/8", 1/32", 5/16" set, black/silver/yellow

-€15.27

JIMS Shouldered Valve Guide Driver Set — 3/8", 1/32", 5/16" set,...

Three-piece shouldered valve guide driver set (3/8", 1/32", 5/16") for guide removal and installation; made in the U.S.A.

€59.39 €74.66

-€5.54

ANDREWS Gauge Pins — 0.105" (2.67 mm) outside diameter, silver

Pins for measuring cam drive gear outside diameters; covers measurement differences between '84–'99 models.

€21.52 €27.06

-€5.90

ANDREWS Gauge Pins — 0.108" outside diameter

Used to measure the outside diameter of cam drive gears. Made in the USA. Ideal for cam gear inspection.

€22.94 €28.84

-€42.29

JIMS Electronic Speedometer Sensor — JIMS, 74437-96

Top-quality replacement speedometer sensor. Fits aftermarket transmission cases with a speedometer sensor hole. Includes O-ring, hardware and OEM connector. Made in the U.S.A.

€164.48 €206.77

-€13.94

MIKUNI Pop-Off Gauge — Black, Air system

Calibrated in 0.5 psi steps to 30 psi for pop-off pressure tuning; EU scale: 0,03 bar to 2,07 bar.

€54.20 €68.14

shop by category

VTwin & Specific Tools

Subcategories

Engine Tools

Contact us

Products

Our company

shop by category

VTwin & Specific Tools  

Subcategories

Engine Tools

VTwin & Specific Tools