VTwin & Specific Tools (3)

-€7.81

JIMS Balancer Shaft Retention Pins — Flywheel assembly, silver

Locks into balancer shaft sprocket pinholes to prevent the balancer from turning out of sync with the flywheel. Use when servicing the flywheel assembly. Made in the U.S.A.

€30.39 €38.20

-€28.78

JIMS Piston Support Plate — JIMS 1164, Black

Non-marring flat plate for pushing piston bottoms during ring or cylinder installation. Made in the U.S.A.

€111.93 €140.71

Compression Release Valve Installation Kit — Engine case fit

-€142.45

JIMS Compression Release Valve Installation Kit — Engine case fit

Complete kit to drill, spot face, tap and install compression release valves on front and rear heads; fits big-inch and high-compression Twin Cams.

€553.95 €696.40

-€73.52

JIMS Wrist Pin Bushing Reaming Tool — Wrist pin, 1726-1

Reams wrist pin bushings to the specified inner diameter. Can be used with rods in or out of the motor. Lead-in taper for easy use. Made in the U.S.A.

€285.92 €359.44

Inner Cam Bearing Go and No-Go Gauges — pair, silver

-€21.59

JIMS Inner Cam Bearing Go and No-Go Gauges — pair, silver

Fast, accurate Go/No‑Go gauges to check the inside diameter of inner cam bearings. Use them to confirm whether the cam will be too loose or too tight. Made in the U.S.A.

€68.14 €89.73

-€26.87

JIMS Fork Seal and Cap Installer — 41 mm fork tube, black

Installs fork and dust seals; lightly grease before use. Made in the U.S.A.

€104.50 €131.37

-€21.50

JIMS Fork Nut Socket — JIMS, Black

Removes and installs the top fork-tube plug; fits 41 mm forks. Made in the U.S.A.

€83.63 €105.13

Exhaust Stud Drill Plate — Blue, anodized

-€40.00

JIMS Exhaust Stud Drill Plate — Blue, anodized

Positions exhaust port seals evenly and works with exhaust flange nuts. Made in the U.S.A.

€155.56 €195.56

Head Bolt Torque Gauge — Torque plate, head bolt application, blue

-€6.19

JIMS Head Bolt Torque Gauge — Torque plate, head bolt application,...

Accurate gauge for measuring 90° when tightening head bolts. Laser-engraved torquing sequence; fits Twin Cam and Evolution engines; made in the U.S.A.

€24.07 €30.26

-€52.24

JIMS Inner Cam Bearing Installation Tool — Right, Black

Presses inner cam bearings to the correct depth for accurate seating. Made in the U.S.A.

€203.16 €255.40

-€38.71

JIMS Clutch Spring Compressor Tool — Blue

Releases the clutch spring for easy retainer ring removal and installation. Made in the USA.

€150.53 €189.24

-€22.12

JIMS Clutch Spring Compressor Nut — Black

Tool for releasing the clutch spring; enables easy retainer ring removal and installation. Made in the USA.

€62.53 €84.65

-€33.12

JIMS Snap Ring Tool — Timken® bearing, black

Tool for removing and installing outer race snap rings on tapered roller bearings. Essential for OEM and aftermarket case ring replacements. Made in the U.S.A.

€128.78 €161.90

Tappet Block Alignment Tool — Crankcase, Black

-€7.15

JIMS Tappet Block Alignment Tool — Crankcase, Black

Precision tool for aligning the crankcase oil hole to the tappet block; also used for Evolution head rocker box bases and Harley-Davidson® Twin Cam oil pump alignment. Made in the U.S.A.

€27.78 €34.93

Transmission Shaft Installer — 5-Speed, Black

-€30.16

JIMS Transmission Shaft Installer — 5-Speed, Black

Installs shafts without the use of a hydraulic or arbor press. Made in the U.S.A.

€117.28 €147.44

-€23.66

JIMS Steering Head Bearing Race Installer — Black

Installs steering head bearing races and frame cups straight and without damage; made in the U.S.A.

€92.01 €115.67

-€51.82

JIMS Main Drive Gear Bearing Removal Tool — 5-Speed, Blue, Silver

Removes old bearings straight without damaging the transmission case; usable without removing the transmission from the bike. Made in the U.S.A.

€201.53 €253.35

Driver Handle — Main drive gear, 5-speed, Blue anodized

-€33.92

JIMS Driver Handle — Main drive gear, 5-speed, Blue anodized

Installs main drive gear oil seal to correct depth with transmission assembled; includes protective sleeve; made in the U.S.A.

€131.92 €165.84

Tappet Oil Filter Screw Plug Tool — Black

-€10.19

JIMS Tappet Oil Filter Screw Plug Tool — Black

Removes tappet oil screen without removing the exhaust. Used to extract the tappet oil screen plug. Made in the U.S.A.

€39.65 €49.84

Shouldered Valve Guide Driver Set — 3/8", 1/32", 5/16" set, black/silver/yellow

-€15.27

JIMS Shouldered Valve Guide Driver Set — 3/8", 1/32", 5/16" set,...

Three-piece shouldered valve guide driver set (3/8", 1/32", 5/16") for guide removal and installation; made in the U.S.A.

€59.39 €74.66

-€42.29

JIMS Electronic Speedometer Sensor — Electronic, Speedometer

Top-quality replacement electronic speedometer sensor. Includes O-ring, hardware and OEM connector. Fits aftermarket transmission cases with a speedometer sensor hole.

€164.48 €206.77

Crankshaft Bearing Tool — Right, Crankcase, Black

-€65.63
Out of Stock

JIMS Crankshaft Bearing Tool — Right, Crankcase, Black

Removes and installs right crankcase bearings without damaging the case.

€255.20 €320.83

-€21.49

JIMS Evolution Cylinder Stud Assembly Tool — Engine

Captive ball-bearing assembly tool set 1" from top for precise stud installs; fits all Evolution Big Twin and XL models. Made in the U.S.A.

€83.58 €105.07

-€395.75

JIMS Timken® Case Bearing Tool — Engine Case, Steel, Black, PN 959

Precision insert sleeve and complete installation hardware to restore case bearing fitment. Requires hand tools and a two-ton press. Timken bearing not included.

€1,539.00 €1,934.75

Balancer Shaft Removal Tool — Left side, engine case, Black

-€72.29

JIMS Balancer Shaft Removal Tool — Left side, engine case, Black

Removes front and rear counter‑balancer shaft bearing assemblies from the left engine case; fits 96" and 110" Beta® engines. Made in the U.S.A.

€281.14 €353.43

Starter Jackshaft Seal Installer Tool — Jackshaft, Black

-€40.67
Out of Stock

JIMS Starter Jackshaft Seal Installer Tool — Jackshaft, Black

Installs the starter jackshaft seal without distortion; fits the seal in the upper part of the inner primary of Big Twins. Made in the U.S.A.

€158.18 €198.85

-€62.84

JIMS Inner Primary Bearing and Seal Remover/Installer Tool — Black kit

Safely removes and installs the inner primary bearing and seal without harming bearings. Made in the USA.

€244.42 €307.26

-€18.28

JIMS O² Sensor Tool — Socket, Silver

Removes and installs oxygen sensors on fuel-injected models. Withstands up to 125 ft.-lbs. Made in the USA.

€71.09 €89.37

Bearing Adapter — Sprocket shaft fit for '06 Harley-Davidson Dyna Glide, '07-'17 Twin Cam

-€28.65
Out of Stock

JIMS Bearing Adapter — Sprocket shaft fit for '06 Harley-Davidson...

Allows installation of a shaft bearing on '06 Harley-Davidson Dyna Glide and '07-'17 Twin Cam; fits sprocket shaft applications and works with compatible bearing tools.

€111.41 €140.06

-€41.24
Out of Stock

JIMS Engine Rotator — flywheel assembly, Black

Rotates the flywheel and piston assembly for pushrod adjustments, engine builds, and clearance checks. Not for use with impact wrenches.

€160.35 €201.59

shop by category

VTwin & Specific Tools

Subcategories

Engine Tools

Contact us

Products

Our company

shop by category

VTwin & Specific Tools  

Subcategories

Engine Tools

VTwin & Specific Tools