VTwin & Specific Tools (2)

JIMS 49mm Fork Seal and Dust Shield Installer — Blue

Installs lower leg 49 mm fork seals squarely without damaging the seal lip. Two-piece design for easier assembly and dust shield cover installation. Made in the U.S.A.

€134.90

Compression Bolt Removal Tool — WP 4860 MXMA CC fit, 17 mm hex, Blue anodized

MOTION PRO Compression Bolt Removal Tool — WP 4860 MXMA CC fit, 17 mm...

Removes and installs the compression valve assembly from the fork cap. 17 mm hex head; enables correct torquing during installation. Use caution — fork cap assembly under pressure.

€13.35

MOTION PRO Gear Jammer™ — Primary gear, Blue anodized

Removes and installs primary gear on Honda CRF450R/X. Locks gears for easy service, allows correct torque on lock nuts, not for impact guns.

€12.13

MOTION PRO Wall Bracket for T-Handle Rack — Chrome, Silver

Mounts a T-handle rack to a toolbox, wall or post; quick-release pin and built-in bottle opener; fits one-piece T-handle racks.

€16.17

ForkTru™ Fork Alignment Tool — 27–62 mm legs, 140–220 mm on center, Blue anodized

MOTION PRO ForkTru™ Fork Alignment Tool — 27–62 mm legs, 140–220 mm on...

Tool for aligning front forks to ensure parallelism from top to bottom. Works with 27–62 mm fork legs and 140–220 mm on-center spacing. Knurled adjustment screws for easy setup and reduced seal/bushing wear.

€28.01

Flywheel Puller Right Hand Internal Thread with M12 Cap — M28 x 1.0, black oxide

MOTION PRO Flywheel Puller Right Hand Internal Thread with M12 Cap — M28...

Heat-treated, high-carbon steel puller with right-hand internal thread and M12 cap. Laser-etched, hot black oxide finish and lifetime limited warranty.

€21.03

MOTION PRO Flywheel Puller Internal Thread — M50 x 1.5, Black oxide

Removes flywheel or rotor. Heat-treated for strength. Laser-etched identification. Includes crank protector. Right-hand thread. Durable corrosion-resistant finish. Lifetime limited warranty.

€60.68

Flywheel Puller/Primary Gear Extractor — Black oxide, Carbon steel

MOTION PRO Flywheel Puller/Primary Gear Extractor — Black oxide, Carbon...

Removes flywheels and rotors; includes 4 mm, 5 mm, and 6 mm hardware. Heat-treated, laser-etched, and backed by a lifetime limited warranty.

€20.87

MOTION PRO Flywheel Puller — Internal thread, M28 x 1.0, Black oxide

Right hand internal-thread puller for removing flywheels or rotors; includes M14 cap and lifetime limited warranty.

€21.85

Flywheel Puller Right Hand Internal Thread — M26 x 1.0, Black oxide

MOTION PRO Flywheel Puller Right Hand Internal Thread — M26 x 1.0, Black...

Precision right-hand internal-thread flywheel puller. Heat treated, laser etched, durable finish and lifetime limited warranty.

€22.44

MOTION PRO Oil Filter Removal Tool — Black, Silver

Conical point screw pierces and grabs the sheet metal end cap for easy removal of recessed KTM oil filters. Not for use on reusable filters.

€9.83

JIMS Cylinder Torque Plate Kit — 3.75"–3.875" bore, black

Use these plates when boring or honing late-model aluminum cylinders to simulate running stress conditions. Includes instructions. Made in the U.S.A.

€598.00

Flywheel Puller Right Hand Internal Thread — M38 x 1.5, black oxide

MOTION PRO Flywheel Puller Right Hand Internal Thread — M38 x 1.5, black...

Right hand internal thread flywheel puller; laser etched, heat treated, high carbon steel, durable finish, lifetime limited warranty.

€39.63

Twin Cam/Evo Crankshaft Runout Measuring Tool — Twin Cam, EVO, Red

FEULING OIL PUMP CORP. Twin Cam/Evo Crankshaft Runout Measuring Tool — Twin Cam, EVO,...

Mounts to the cam chest to measure crankshaft run out and Twin Cam gear drive backlash. Includes tool plate, +/- 0.001 dial indicator, and mounting hardware.

€99.12

MOTION PRO Deluxe Piston Pin Puller — Blue anodized

Removes piston pins from full skirt and short skirt (slipper) pistons. Fits pins 12 mm (1/2") to 24 mm (1"). Non-marring aluminum pin adapters and interchangeable piston adapters.

€41.67

HOT CAMS Metric Cam Installation Kit — Blue

Comprehensive installation kit for camshaft work. Includes degree wheel, dial indicator with long and short reach studs, adjustable magnetic stand, three positive stops (10 mm, 12 mm, 14 mm threads) and a wooden carrying case.

€198.31

K&L SUPPLY Cam Chain Tensioner Holder — Cam, Black/Silver

Holds the cam chain tensioner during removal and installation. Tabs engage the tensioner slots; knob retracts the tensioner; includes a one-way bearing.

€90.30

K&L SUPPLY Kwik-Loader Valve Keeper Tool Set — Valve assembly, Black/White

Two-tool set that speeds keeper removal and installation using a removal tool and a hand-operated installation tool for fast, reliable valve service.

€167.39

FEULING OIL PUMP CORP. Pushrod Tube Holder — Pushrod Tube, Black

Holds pushrod tubes up and out of the way for easy adjustment. Fits EVO, TC and most aftermarket tubes.

€14.65

JIMS Replacement Drive — Cam, Black

Replacement drive for JIMS® cam bearing installation tool — durable, precision-fit component.

€87.48

JIMS Pushrod Cover Clip — Pushrod, Black

Quick one-hand tool for installing and removing cover clips. Won't mar or slip. Made in the U.S.A.

€81.28

JIMS Dual Gauge Leakdown Tester — JIMS, Cylinder, 4-Stroke, Black

Dual-gauge design for quick leakdown diagnosis; detects valve-seat leaks, bad rings and head gasket failures.

€166.40

JIMS Hydraulic Balancer Retainer Tool — Engine balancer, Silver

Holds hydraulic tensioners to maintain constant chain tension on counter balancer systems. Made in the U.S.A.

€39.72

JIMS Mini Valve Spring Tester — Black, Blue

Compact tester for dual-rate and conical valve springs; fits up to 1.6" O.D.; 0–1000 P.S.I. gauge. Made in the U.S.A.

€184.35

MOTION PRO Side Jaw Pincer Tool — Black, Blue

Compact side-jaw tool for installing Stepless® ear clamps in tight spaces.

€30.07

JIMS Dipstick Removal Tool — Engine oil system, Gray

Safely removes engine oil dipsticks near hot exhausts; fits 3/8" ratchet and 7/8" wrench. Made in the U.S.A.

€29.41

KIBBLEWHITE Valve Guide Ball Hone — 7.0 mm, Black, Silver

Ball hone for sizing valve guide materials; durable for C630 bronze and cast iron. Made in the U.S.A.

€22.36

JIMS Mighty Bite Flywheel Lock and Tag — Blue

Secures the flywheel for service on Twin Cam motors; installs in place of the crank position sensor and includes a visible decommissioned tag.

€49.23

$Piston Ring End Gap Tool — Fits H-D 95\", 103\", 110\" motors, 3.875\" or 4\" bore, blue anodized$

JIMS Piston Ring End Gap Tool — Fits H-D 95\", 103\", 110\" motors,...

Measures piston ring end gap quickly and accurately. Flanged design ensures a square fit in the bore. Fits H-D 95\", 103\", 110\" motors with 3.875\" or 4\" bore.

€85.30

MOTION PRO Flywheel Puller with Thread Protector — M26 x 1.0, Black oxide

Professional puller for safe flywheel and rotor removal. Heat treated, laser-etched, includes thread protector and lifetime limited warranty.

€20.22

shop by category

VTwin & Specific Tools

Subcategories

Engine Tools

Contact us

Products

Our company

shop by category

VTwin & Specific Tools  

Subcategories

Engine Tools

VTwin & Specific Tools