TOOLS (8)

-€10.86

TECMATE Battery to USB-C Charger — 12V, 3300mA

Weatherproof USB-C charging cable that mounts where you need a port; automatic protections, battery monitor and simple installation for powersport use.

€23.27 €34.13

-€1.84

TECMATE OptiMate Swivelling Charger HOOK — Black, fits OptiMate chargers

Swivelling mount to hang your OptiMate charger on handlebars, struts or cables; velcro included for neat wire management.

€3.95 €5.79

-€10.06

TECMATE OptiMate USB O-119 — 3300 mA, 5 V, Blue

Weatherproof portable dual USB charger with in-line 180° BIKE plug for BMW, Triumph and Ducati Multistrada. Fast, safe charging for USB‑A and USB‑C devices with automatic one-hour shutoff to protect the vehicle battery.

€21.57 €31.63

-€3.70

TECMATE OptiMate CABLE O-49 — 24V, Black

SAE to XLR 3-pin adapter cable for 24V battery charging. Length 30 cm / 12". Rubber in-line seal, thicker insulation, 10 A avg / 13 A max.

€7.93 €11.63

-€9.79

TECMATE OptiMate USB O-114 — 5 V, 3.3 A, Blue

Portable dual-output USB charger with USB-A and USB-C and a 90° DIN BIKE plug for BMW and Triumph. Built-in one-hour safety shutoff to prevent draining a parked vehicle battery.

€21.00 €30.79

-€101.63

TECMATE OptiMate Pro-4 DUO — 4 charging banks, 12V 5A

Automatic diagnostic charger for four batteries with independent banks; activates new batteries, saves deeply discharged units, and runs state‑of‑health tests. Replaceable output cords and service‑oriented design.

€397.66 €499.29

Reverse Brake Bleeder Tool — Single- and dual-disc, with or without ABS, Black

-€46.39

JIMS Reverse Brake Bleeder Tool — Single- and dual-disc, with or...

Innovative reverse bleeding method removes all air without pumping; pushes fresh fluid through the master cylinder, follows OEM ABS procedures, saves time and fluid, made in the U.S.A.

€180.40 €226.79

-€9.57

JIMS 25 mm Wheel Bearing Adapter — Black, Metric

Precision 25 mm adapter for Harley-Davidson® models from '07 to '19. Made in the USA.

€37.23 €46.80

-€13.22

JIMS Rear Axle Installation Guide Tool — JIMS, Rear Axle, Black

Tool for aligning rear wheel, caliper brackets, hubs and spacers on Big Twin models with hollow 1" (25 mm) standard axles. Made in the USA.

€51.42 €64.64

Primary Locking Bar — Primary Belt Drive, Primary Chain Drive, Black

-€9.57

JIMS Primary Locking Bar — Primary Belt Drive, Primary Chain Drive,...

Immobilizes the primary drive for safe tightening and loosening during maintenance. Prevents rotor and magnet damage.

€37.23 €46.80

Primary Locking Bar — Primary (drive), Black

-€9.57

JIMS Primary Locking Bar — Primary (drive), Black

Immobilizes the primary drive; allows torque-wrench tightening or breaker-bar loosening; prevents rotor and magnet damage; made in the U.S.A.

€37.23 €46.80

-€20.91

BARNETT Clutch Spring Compression Tool — Black

Compresses diaphragm clutch springs for easy removal and reinstallation of retainer rings. Made in the USA.

€81.32 €102.23

-€11.50

BARNETT Clutch Spring Compression Tool — Black

Tool for removal and reinstallation of retainer rings on diaphragm clutches. Durable and compact for shop or home use. Made in the USA.

€44.69 €56.19

$MagCode® 12 V Magnetic Connector Clip Cable — 12V, 75 cm (30\"), 10A (13A max), MagCode-to-SAE$

-€17.22

TECMATE MagCode® 12 V Magnetic Connector Clip Cable — 12V, 75 cm...

MagCode® 12 V magnetic connector clip cable with 75 cm nylon-sleeved 16 AWG cable, SAE termination, and rubber in-line seal.

€36.91 €54.13

MagCode® 12 V Magnetic Port Panel Mount Kit — Magnetic panel mount, MagCode

-€22.20

TECMATE MagCode® 12 V Magnetic Port Panel Mount Kit — Magnetic panel...

Panel-mount MagCode® 12 V kit with 40 in cable, 16 AWG SPT2-W, 10 A (13 A max) rating and 15 A fuse. Weatherproof sealing cap and ring terminal connectors.

€62.75 €84.95

-€32.08
New

JIMS M8 Shifter Shaft Bushing Remover & Installer — 5512, Black, Kit

Toolset for quick removal and precise installation of shifter shaft bushings to the correct depth.

€124.76 €156.84

Crankshaft Bearing Tool — Right, Crankcase, Black

-€65.63
Out of Stock

JIMS Crankshaft Bearing Tool — Right, Crankcase, Black

Removes and installs right crankcase bearings without damaging the case.

€255.20 €320.83

-€21.49
Out of Stock

JIMS Evolution Cylinder Stud Assembly Tool — Engine

Captive ball-bearing assembly tool set 1" from top for precise stud installs; fits all Evolution Big Twin and XL models. Made in the U.S.A.

€83.58 €105.07

-€17.00
Out of Stock

JIMS Primary Locking Bar — Front engine sprocket, Black

Immobilizes the primary drive for clutch and primary-drive service. Allows torque-wrench tightening or breaker-bar loosening. Made in the U.S.A.

€66.14 €83.14

-€29.18
Out of Stock

JIMS Cruise Drive Vise Stand — Black, Blue

Aligns transmission gears and shafts for safe, damage-free installation; speeds and simplifies assembly.

€113.50 €142.68

-€12.99
Out of Stock

JIMS Shifter Shaft Sleeve Tool — For 5-Speed Transmission, Black

Removes and installs shifter shaft sleeves, assemblies and drums. Made in the USA.

€50.45 €63.44

Main Drive Gear Bearing/Seal Installation Tool — Cruise Drive, 6-speed, Black

-€38.43
Out of Stock

JIMS Main Drive Gear Bearing/Seal Installation Tool — Cruise Drive,...

Precision installer for main drive gear bearings and seal; prevents marring and seats components to correct depth using a one-ton press. Made in USA.

€149.48 €187.91

-€56.85
Out of Stock

JIMS Transmission Door Puller — Blue

Removes transmission door with gears and shaft attached. Will not damage door bearings. Made in the USA.

€221.03 €277.88

-€395.75
Out of Stock

JIMS Timken® Case Bearing Tool — Engine Case, Steel, Black, PN 959

Precision insert sleeve and complete installation hardware to restore case bearing fitment. Requires hand tools and a two-ton press. Timken bearing not included.

€1,539.00 €1,934.75

-€57.61
Out of Stock

JIMS Transmission Sprocket Locknut Wrench — Black

Extra-long two-piece wrench designed to remove the hex nut at the end of the main drive gear. Inner collar retains wrench to nut for safer work.

€224.02 €281.63

Balancer Shaft Removal Tool — Left side, engine case, Black

-€72.29
Out of Stock

JIMS Balancer Shaft Removal Tool — Left side, engine case, Black

Removes front and rear counter‑balancer shaft bearing assemblies from the left engine case; fits 96" and 110" Beta® engines. Made in the U.S.A.

€281.14 €353.43

Bearing and Race Puller Tool — Pinion shaft, flywheel bearing race, Black

-€109.87
Out of Stock

JIMS Bearing and Race Puller Tool — Pinion shaft, flywheel bearing...

Precision tool for removing press-fit bearings and gears from motorcycle pinion and flywheel shafts. Multi-use and made in the U.S.A.

€427.30 €537.17

Sealed Wheel Bearing Removal/Installation Kit — 3/4", 1", 25 mm

-€114.88
Out of Stock

JIMS Sealed Wheel Bearing Removal/Installation Kit — 3/4", 1", 25 mm

Removes and installs 3/4" , 1" and 25 mm sealed wheel bearings, with or without ABS. Made in the USA.

€446.75 €561.63

Starter Jackshaft Seal Installer Tool — Jackshaft, Black

-€40.67
Out of Stock

JIMS Starter Jackshaft Seal Installer Tool — Jackshaft, Black

Installs the starter jackshaft seal without distortion; fits the seal in the upper part of the inner primary of Big Twins. Made in the U.S.A.

€158.18 €198.85

Harley Davidson Cruise Drive 6-Speed Main Drive Gear Remover Tool — Black

-€64.36
Out of Stock

JIMS Harley Davidson Cruise Drive 6-Speed Main Drive Gear Remover...

Removes the main drive gear from the main bearing while in the transmission case without requiring an arbor press.

€250.28 €314.64

shop by category

TOOLS

Subcategories

General Tools

VTwin & Specific Tools

Workshop Equipment

Contact us

Products

Our company

shop by category

TOOLS  

Subcategories

General Tools

VTwin & Specific Tools

Workshop Equipment

TOOLS