TOOLS (5)

-€5.39

JIMS Spark Plug and O² Sensor Thread Chaser — M18 x 1.5 thread, Black

Three-flute thread chaser with a generous lead-in pilot; repairs damaged internal threads without cutting oversize threads. Made in the USA.

€20.94 €26.33

-€19.01

JIMS Ignition Switch Fork Lock Tool — Fork lock, Black

Locates on ignition switch face nut to hold switch for removal or installation. 3/8" drive access hole. Made in the USA.

€73.93 €92.94

Multimeter Volt Probe Kit — JIMS Kit, Black, Blue, Green, Red, Yellow

-€24.75

JIMS Multimeter Volt Probe Kit — JIMS Kit, Black, Blue, Green, Red,...

Color‑coded, fully insulated probes with 180°, 45°, 90° options and 4 mm banana plugs for safe, precise diagnostics.

€96.26 €121.01

Ignition Switch Housing Alignment Tool — Vendor Part Number 944, Blue

-€29.85

JIMS Ignition Switch Housing Alignment Tool — Vendor Part Number...

Aligns the ignition switch housing during screw torquing to ensure correct switch orientation and longer housing life.

€116.08 €145.93

-€14.87

JIMS Battery Lifter — 5501, Silver

Modeled after larger automotive battery tools but sized for Harley-Davidson® models; easily lifts batteries with extremely tight fits. Made in the USA.

€57.83 €72.70

Reverse Brake Bleeder Tool — Single- and dual-disc, with or without ABS, Black

-€46.39

JIMS Reverse Brake Bleeder Tool — Single- and dual-disc, with or...

Innovative reverse bleeding method removes all air without pumping; pushes fresh fluid through the master cylinder, follows OEM ABS procedures, saves time and fluid, made in the U.S.A.

€180.40 €226.79

-€9.57

JIMS 25 mm Wheel Bearing Adapter — Black, Metric

Precision 25 mm adapter for Harley-Davidson® models from '07 to '19. Made in the USA.

€37.23 €46.80

-€13.22

JIMS Rear Axle Installation Guide Tool — JIMS, Rear Axle, Black

Tool for aligning rear wheel, caliper brackets, hubs and spacers on Big Twin models with hollow 1" (25 mm) standard axles. Made in the USA.

€51.42 €64.64

-€4.86

PEDRO'S Freewheel L Hex Wrench 12 mm — Gray

L-shaped 12mm hex wrench with extra length for improved leverage and reach. Heat-treated tool steel construction for lasting performance.

€8.17 €13.03

Primary Locking Bar — Primary (drive), Black

-€9.57

JIMS Primary Locking Bar — Primary (drive), Black

Immobilizes the primary drive; allows torque-wrench tightening or breaker-bar loosening; prevents rotor and magnet damage; made in the U.S.A.

€37.23 €46.80

-€20.91

BARNETT Clutch Spring Compression Tool — Black

Compresses diaphragm clutch springs for easy removal and reinstallation of retainer rings. Made in the USA.

€81.32 €102.23

-€11.50

BARNETT Clutch Spring Compression Tool — Black

Tool for removal and reinstallation of retainer rings on diaphragm clutches. Durable and compact for shop or home use. Made in the USA.

€44.69 €56.19

-€32.08

JIMS M8 Shifter Shaft Bushing Remover & Installer — 5512, Black, Kit

Toolset for quick removal and precise installation of shifter shaft bushings to the correct depth.

€124.76 €156.84

-€10.87
New

PEDRO'S PJs Discontinued — Vendor Part Number 6451311

A discontinued PJs model valued by collectors and riders alike.

€30.72 €41.59

Pro BB Wrench 16-Notch x 44mm — 3/8" drive, Black

-€7.14
New

PEDRO'S Pro BB Wrench 16-Notch x 44mm — 3/8" drive, Black

4mm laser-cut, heat-treated tool steel
Fits 16-notch external BB cups and rotor lockrings
3/8" drive for torque wrenches

€20.17 €27.31

-€5.42
New

PEDRO'S Downhill Tire Lever II — Black, Yellow

Compact, toolbox-friendly tool with heat-treated steel; large shovel tip for strong bead retention; ergonomic dual-density screwdriver-style handle; also removes fork seals.

€15.33 €20.75

Crankshaft Bearing Tool — Right, Crankcase, Black

-€65.63

JIMS Crankshaft Bearing Tool — Right, Crankcase, Black

Removes and installs right crankcase bearings without damaging the case.

€255.20 €320.83

-€21.49

JIMS Evolution Cylinder Stud Assembly Tool — Engine

Captive ball-bearing assembly tool set 1" from top for precise stud installs; fits all Evolution Big Twin and XL models. Made in the U.S.A.

€83.58 €105.07

-€17.00
Out of Stock

JIMS Primary Locking Bar — Front engine sprocket, Black

Immobilizes the primary drive for clutch and primary-drive service. Allows torque-wrench tightening or breaker-bar loosening. Made in the U.S.A.

€66.14 €83.14

-€29.18
Out of Stock

JIMS Cruise Drive Vise Stand — Black, Blue

Aligns transmission gears and shafts for safe, damage-free installation; speeds and simplifies assembly.

€113.50 €142.68

-€12.99

JIMS Shifter Shaft Sleeve Tool — For 5-Speed Transmission, Black

Removes and installs shifter shaft sleeves, assemblies and drums. Made in the USA.

€50.45 €63.44

Main Drive Gear Bearing/Seal Installation Tool — Cruise Drive, 6-speed, Black

-€38.43

JIMS Main Drive Gear Bearing/Seal Installation Tool — Cruise Drive,...

Precision installer for main drive gear bearings and seal; prevents marring and seats components to correct depth using a one-ton press. Made in USA.

€149.48 €187.91

-€56.85

JIMS Transmission Door Puller — Blue

Removes transmission door with gears and shaft attached. Will not damage door bearings. Made in the USA.

€221.03 €277.88

-€395.75

JIMS Timken® Case Bearing Tool — Engine Case, Steel, Black, PN 959

Precision insert sleeve and complete installation hardware to restore case bearing fitment. Requires hand tools and a two-ton press. Timken bearing not included.

€1,539.00 €1,934.75

Balancer Shaft Removal Tool — Left side, engine case, Black

-€72.29

JIMS Balancer Shaft Removal Tool — Left side, engine case, Black

Removes front and rear counter‑balancer shaft bearing assemblies from the left engine case; fits 96" and 110" Beta® engines. Made in the U.S.A.

€281.14 €353.43

Sealed Wheel Bearing Removal/Installation Kit — 3/4", 1", 25 mm

-€114.88

JIMS Sealed Wheel Bearing Removal/Installation Kit — 3/4", 1", 25 mm

Removes and installs 3/4" , 1" and 25 mm sealed wheel bearings, with or without ABS. Made in the USA.

€446.75 €561.63

Starter Jackshaft Seal Installer Tool — Jackshaft, Black

-€40.67

JIMS Starter Jackshaft Seal Installer Tool — Jackshaft, Black

Installs the starter jackshaft seal without distortion; fits the seal in the upper part of the inner primary of Big Twins. Made in the U.S.A.

€158.18 €198.85

Harley Davidson Cruise Drive 6-Speed Main Drive Gear Remover Tool — Black

-€64.36

JIMS Harley Davidson Cruise Drive 6-Speed Main Drive Gear Remover...

Removes the main drive gear from the main bearing while in the transmission case without requiring an arbor press.

€250.28 €314.64

-€62.84

JIMS Inner Primary Bearing and Seal Remover/Installer Tool — Black kit

Safely removes and installs the inner primary bearing and seal without harming bearings. Made in the USA.

€244.42 €307.26

-€18.28

JIMS O² Sensor Tool — Socket, Silver

Removes and installs oxygen sensors on fuel-injected models. Withstands up to 125 ft.-lbs. Made in the USA.

€71.09 €89.37

shop by category

TOOLS

Subcategories

General Tools

VTwin & Specific Tools

Workshop Equipment

Contact us

Products

Our company