TOOLS (2)

-€2.27

MOTION PRO Float Bowl Wrench — Silver anodized

Removes 17 mm float bowl drain plugs; doubles as a high-speed compression adjuster for most Showa, KYB, and WP rear shocks. 12-point, low-profile design.

€7.36 €9.63

Seal/Bearing Retainer Tool — 47 mm lock rings, 22 mm hex, silver

-€6.98

MOTION PRO Seal/Bearing Retainer Tool — 47 mm lock rings, 22 mm hex, silver

Precision tool to remove and replace rear wheel bearing/seal retainer rings for 47 mm lock rings; features a 22 mm hex.

€22.68 €29.66

Compression Bolt Removal Tool — WP 4860 MXMA CC fit, 17 mm hex, Blue anodized

-€4.40

MOTION PRO Compression Bolt Removal Tool — WP 4860 MXMA CC fit, 17 mm...

Removes and installs the compression valve assembly from the fork cap. 17 mm hex head; enables correct torquing during installation. Use caution — fork cap assembly under pressure.

€14.28 €18.68

Gear Jammer™ — Primary gear, Blue anodized

-€3.98

MOTION PRO Gear Jammer™ — Primary gear, Blue anodized

Removes and installs primary gear on Honda CRF450R/X. Locks gears for easy service, allows correct torque on lock nuts, not for impact guns.

€12.98 €16.96

Wall Bracket for T-Handle Rack — Chrome, Silver

-€5.32

MOTION PRO Wall Bracket for T-Handle Rack — Chrome, Silver

Mounts a T-handle rack to a toolbox, wall or post; quick-release pin and built-in bottle opener; fits one-piece T-handle racks.

€17.29 €22.61

ForkTru™ Fork Alignment Tool — 27–62 mm legs, 140–220 mm on center, Blue anodized

-€9.22

MOTION PRO ForkTru™ Fork Alignment Tool — 27–62 mm legs, 140–220 mm on...

Tool for aligning front forks to ensure parallelism from top to bottom. Works with 27–62 mm fork legs and 140–220 mm on-center spacing. Knurled adjustment screws for easy setup and reduced seal/bushing wear.

€29.95 €39.17

Flywheel Puller Right Hand Internal Thread with M12 Cap — M28 x 1.0, black oxide

-€6.93

MOTION PRO Flywheel Puller Right Hand Internal Thread with M12 Cap — M28...

Heat-treated, high-carbon steel puller with right-hand internal thread and M12 cap. Laser-etched, hot black oxide finish and lifetime limited warranty.

€22.49 €29.42

-€19.98

MOTION PRO Flywheel Puller Internal Thread — M50 x 1.5, Black oxide

Removes flywheel or rotor. Heat-treated for strength. Laser-etched identification. Includes crank protector. Right-hand thread. Durable corrosion-resistant finish. Lifetime limited warranty.

€64.89 €84.87

Flywheel Puller/Primary Gear Extractor — Black oxide, Carbon steel

-€6.86

MOTION PRO Flywheel Puller/Primary Gear Extractor — Black oxide, Carbon...

Removes flywheels and rotors; includes 4 mm, 5 mm, and 6 mm hardware. Heat-treated, laser-etched, and backed by a lifetime limited warranty.

€22.32 €29.18

-€7.19

MOTION PRO Flywheel Puller — Internal thread, M28 x 1.0, Black oxide

Right hand internal-thread puller for removing flywheels or rotors; includes M14 cap and lifetime limited warranty.

€23.36 €30.55

Flywheel Puller Right Hand Internal Thread — M26 x 1.0, Black oxide

-€7.38

MOTION PRO Flywheel Puller Right Hand Internal Thread — M26 x 1.0, Black...

Precision right-hand internal-thread flywheel puller. Heat treated, laser etched, durable finish and lifetime limited warranty.

€24.00 €31.38

-€3.24

MOTION PRO Oil Filter Removal Tool — Black, Silver

Conical point screw pierces and grabs the sheet metal end cap for easy removal of recessed KTM oil filters. Not for use on reusable filters.

€10.52 €13.76

Flywheel Puller Right Hand Internal Thread — M38 x 1.5, black oxide

-€13.04

MOTION PRO Flywheel Puller Right Hand Internal Thread — M38 x 1.5, black...

Right hand internal thread flywheel puller; laser etched, heat treated, high carbon steel, durable finish, lifetime limited warranty.

€42.39 €55.43

Twin Cam/Evo Crankshaft Runout Measuring Tool — Twin Cam, EVO, Red

-€22.72

FEULING OIL PUMP CORP. Twin Cam/Evo Crankshaft Runout Measuring Tool — Twin Cam, EVO,...

Mounts to the cam chest to measure crankshaft run out and Twin Cam gear drive backlash. Includes tool plate, +/- 0.001 dial indicator, and mounting hardware.

€106.01 €128.73

-€13.72

MOTION PRO Deluxe Piston Pin Puller — Blue anodized

Removes piston pins from full skirt and short skirt (slipper) pistons. Fits pins 12 mm (1/2") to 24 mm (1"). Non-marring aluminum pin adapters and interchangeable piston adapters.

€44.56 €58.28

-€3.36

FEULING OIL PUMP CORP. Pushrod Tube Holder — Pushrod Tube, Black

Holds pushrod tubes up and out of the way for easy adjustment. Fits EVO, TC and most aftermarket tubes.

€15.67 €19.03

Counter Balancer and Clutch Hub Spanner for Honda — 20 mm ID, 3/8" driver, 4-pin spanner

-€2.67

MOTION PRO Counter Balancer and Clutch Hub Spanner for Honda — 20 mm ID,...

Heat-treated 4-pin spanner for removing Honda counter balancer and clutch hub nuts. 20 mm ID, for use with a 3/8" driver.

€8.67 €11.34

-€9.90

MOTION PRO Side Jaw Pincer Tool — Black, Blue

Compact side-jaw tool for installing Stepless® ear clamps in tight spaces.

€32.16 €42.06

-€6.66

MOTION PRO Flywheel Puller with Thread Protector — M26 x 1.0, Black oxide

Professional puller for safe flywheel and rotor removal. Heat treated, laser-etched, includes thread protector and lifetime limited warranty.

€21.62 €28.28

Flywheel/Rotor Puller Internal Thread — M40 x 1.5, right-hand thread

-€11.98

MOTION PRO Flywheel/Rotor Puller Internal Thread — M40 x 1.5, right-hand...

Internal-thread design protects the crankshaft during rotor removal.
Laser-etched identification for easy tracking.
Heat treated and finished for durability; lifetime limited warranty.

€38.94 €50.92

Dowel Pin Puller Set — Engine case, black

-€20.20

MOTION PRO Dowel Pin Puller Set — Engine case, black

Compact kit with puller rod and slide hammer for stuck dowel pins. Includes 8 mm, 10 mm, 12 mm and 14 mm collets and a storage tray.

€65.67 €85.87

Crankcase Splitter V2 — Aluminum and steel, black and blue anodized

-€45.58

MOTION PRO Crankcase Splitter V2 — Aluminum and steel, black and blue...

Fast, easy-to-use crankcase splitter with 5 mm, 6 mm and 8 mm puller stud threads, captured retaining collars, grooved studs and molded storage tray.

€212.69 €258.27

Clutch Adjuster Nut Tool — 11/16" clutch adjuster lock nut, fits '98 and later Big Twin Harley-Davidson models, black

-€3.94

MOTION PRO Clutch Adjuster Nut Tool — 11/16" clutch adjuster lock nut,...

Through-hole design holds the clutch adjuster screw while tightening the 11/16" lock nut; deep socket fits into the clutch basket; compact for saddlebags. Not for hydraulic clutches.

€12.84 €16.78

Crankshaft Puller — 25 mm & 40 mm adapters, M10x1.25/M12x1.25, Blue anodized

-€24.37

MOTION PRO Crankshaft Puller — 25 mm & 40 mm adapters, M10x1.25/M12x1.25,...

Precision crankshaft puller with 25 mm and 40 mm adapters and reversible M10x1.25/M12x1.25 studs for fast, accurate installs.

€79.18 €103.55

Countershaft Seal Puller — 29–47 mm, black

-€18.11

MOTION PRO Countershaft Seal Puller — 29–47 mm, black

Removes countershaft seals 29–47 mm without damaging engine cases. Designed for off-road, street and ATV engines.

€58.88 €76.99

T-6 Valve Spring Compressor — 24 mm, Blue anodized

-€34.81

MOTION PRO T-6 Valve Spring Compressor — 24 mm, Blue anodized

Quick-release, fully adjustable valve spring compressor compatible with most motorcycle, ATV, UTV, and small engine cylinder heads.

€113.14 €147.95

-€8.93

FEULING OIL PUMP CORP. M8 Oil Pump Roll Pin Remover/Installer Tool — Red

Quick, precise tool for removing and installing the roll pin in M8 oil pumps. Made in the USA.

€41.66 €50.59

Measuring Balls for No Go™ Lifter Bore Kit — No Go lifter bore set, Silver

-€39.69

FEULING OIL PUMP CORP. Measuring Balls for No Go™ Lifter Bore Kit — No Go lifter bore...

Precision measuring balls for checking lifter bore diameter and roundness. Includes four sizes (0.8430"–0.8450") and fits EVO '84-'99, Twin Cam '99-'17 and M8 '17-'24. Made in the USA.

€185.21 €224.90

-€22.72

FEULING OIL PUMP CORP. M8 Crankshaft Runout Measuring Tool — Red

Quickly and accurately checks crank pinion shaft runout on M8 engines with the crankshaft installed. Includes dial indicator, tool plate, and mounting hardware.

€106.01 €128.73

-€3.72

MOTION PRO Torx Bit Set — T25/T30, T40/T45, 1/4" drive fit

Rubber O-ring secures double-ended Torx bits. Sizes T25/T30 and T40/T45. Fits 1/4" drive with 5/16" socket or 5/16" T-handle. Compatible with Motion Pro MP08-161.

€12.11 €15.83

shop by category

TOOLS

Subcategories

General Tools

VTwin & Specific Tools

Workshop Equipment

Contact us

Products

Our company