Camshafts (10)

-€2.57

EASTERN MOTORCYCLE PARTS Cam Shims — 0.005", 10-pack

Essential shims for precise cam setup. Made in the USA.

€7.27 €9.84

-€2.57

EASTERN MOTORCYCLE PARTS Cam Shims — 0.010", 2nd gear, 10-pack

Precision shims for setting up new cams. Made in the USA.

€7.27 €9.84

$Cam Gear Thrust Washers — Size 0.040\", 5-pack$

-€4.70

EASTERN MOTORCYCLE PARTS Cam Gear Thrust Washers — Size 0.040\", 5-pack

Absorbs axial camshaft loads; precision machined; made in the USA.

€13.25 €17.95

-€51.96

ANDREWS A2 Grind Cam — Exhaust 248° / Intake 242°

Fits 1966–1984 Big Twin engines (except 1980–1981). Increases mid-range and top-end power; idle is unaffected. Check spring travel and clearances on 1980+ models.

€202.08 €254.04

A2 Grind Cam — Fits 1966–1984 Big Twin (except 1980–1981)

-€44.64

ANDREWS A2 Grind Cam — Fits 1966–1984 Big Twin (except 1980–1981)

Bolts into 1966–1984 Big Twin engines (except 1980–1981); increases mid- and high-rpm power while preserving idle.

€173.65 €218.29

B2 Grind Cam — Andrews, B2 grind, Gear type

-€51.96

ANDREWS B2 Grind Cam — Andrews, B2 grind, Gear type

More mid-range and high-end power for street/strip with a smooth idle; ideal for 74/80-inch and small stroker engines.

€202.08 €254.04

-€51.96

ANDREWS B2 Grind Cam — Gear, Intake 256°, Exhaust 258°

Best cam for 74/80 inchers and small strokers; delivers strong mid and high-end power with a smooth idle. Spring spacing and main bearing boss clearance must be checked.

€202.08 €254.04

-€51.96
Out of Stock

ANDREWS 7 Grind Cam — 7 Series, 268° intake/exhaust

Great street cam for 84–88-inch strokers; upgraded from the #6 grind with strong torque from 2,200–6,500 rpm.

€202.08 €254.04

7 Grind Cam — 7 Series, 268° intake/exhaust, 56° exhaust open, 29° intake open

-€51.96

ANDREWS 7 Grind Cam — 7 Series, 268° intake/exhaust, 56° exhaust open,...

Great street cam for 84/88-inch strokers; upgraded replacement for the #6 grind, boosting torque from 2,200–6,500 rpm.

€202.08 €254.04

450S Cam — Intake 236°, Exhaust 238°, Lift 0.475"

-€57.28

S&S CYCLE 450S Cam — Intake 236°, Exhaust 238°, Lift 0.475"

Dyno-tested S&S 450S cam delivering good low and mid-range torque. Bolt-in for lower compression motors up to 8.5:1. Recommend hydraulic lifters. Made in USA.

€222.75 €280.03

Reaper® 525 Cam — 525 Series grind, 236° exhaust duration, 226° intake duration

-€119.78

FEULING OIL PUMP CORP. Reaper® 525 Cam — 525 Series grind, 236° exhaust duration,...

Bolt-in camshaft upgrade for stock 88" and 96" engines; widens the torque band, improves throttle response and fuel economy.

€338.55 €458.33

-€140.55

FEULING OIL PUMP CORP. Reaper® Camshaft 574 Series — Intake 240°, Exhaust 255°

Bolt-in performance camshaft for 96", 103" and 110" engines with a smooth cam-lobe for quiet valvetrain operation.

€397.27 €537.82

Reaper® 630 Cam — 263° exhaust, 258° intake, 0.630" lift

-€94.15
Out of Stock

FEULING OIL PUMP CORP. Reaper® 630 Cam — 263° exhaust, 258° intake, 0.630" lift

Wide 2500–6900+ RPM power range
Requires carburetor/throttle body tuning and performance exhaust/intake
High-performance valve springs, pushrods and lifters required
Made in the USA

€366.15 €460.30

Reaper® 630 Cam — 630 Series grind, 263° exhaust duration, 39° overlap

-€94.15

FEULING OIL PUMP CORP. Reaper® 630 Cam — 630 Series grind, 263° exhaust duration, 39°...

High‑performance camshaft that boosts mid and top end power while retaining low‑end performance. Requires carb/throttle body tuning and supporting exhaust and intake systems. Professional installation recommended.

€366.15 €460.30

-€27.33

FEULING OIL PUMP CORP. Camshaft Installation Kit — Camshaft kit, Part 2065

Complete camshaft installation kit with quick change gaskets and premium roller bearings for reliable camplate service.

€106.26 €133.59

-€2.53

FEULING OIL PUMP CORP. Bearing Retainer Plate — Cam, steel

Cam bearing retainer plate and hardware; fits Twin Cam model cam plates. Not for '06 Dyna or Screamin' Eagle support plates.

€9.88 €12.41

-€7.77
Out of Stock

FEULING OIL PUMP CORP. Camplate Chain Tensioner Pins — Pair

Pair of precision pins that ensure correct press fit when servicing Twin Cam chain drive cam plates and tensioners.

€30.23 €38.00

-€133.25

FEULING OIL PUMP CORP. High Flow Camplate — Chain conversion

Increases engine oil flow and cooling; pressure-tested with relief valve set to 55–60 psi. Includes bearing and retainer plate hardware. For use only with Feuling® oil pumps.

€376.59 €509.84

-€121.44

S&S CYCLE 570 Easy Start Camshaft Kit — 570 Series grind, Chain

Temporarily reduces crank compression for easier starts, bolt-in kit that increases power from 3200–5700 rpm; includes camshafts and hardware. Installer must verify clearances. Not for models with OEM compression releases.

€472.27 €593.71

-€112.20

S&S CYCLE 585 Easy Start Camshaft Kit — 88–124 CID, 585 Series grind

Easy-start camshaft kit for select 88–124 CID engines. Bolt-in installation; includes required hardware. Installer must verify clearances.

€436.38 €548.58

-€222.31

S&S CYCLE 551 Easy Start Camshaft Kit — Easy Start, Gear

Easy-start camshaft kit that reduces compression at startup for easier cranking; bolt-in for stock or mildly modified Touring models. Includes camshafts and installation hardware. Not for models with OEM compression releases.

€864.53 €1,086.84

-€240.61

S&S CYCLE 585 Easy Start Camshaft Kit — 585 Series grind, gear type

Eases cold starts by reducing starting compression; bolt-in kit with all required hardware. Not for models with OEM compression releases.

€935.67 €1,176.28

-€94.15

FEULING OIL PUMP CORP. Reaper® Camshaft 574 Series — Chain, Intake 240°, Exhaust 255°

Broad power band for modified engines; bolt-in for stock 96", 103" and 110" engines. Smooth cam-lobe design; rpm range 2100–6500.

€366.15 €460.30

570C Camshaft Kit — 570 Series grind, Chain, Exhaust 255°, Intake 240°

-€93.94

S&S CYCLE 570C Camshaft Kit — 570 Series grind, Chain, Exhaust 255°,...

Designed for 88"–103" CID engines (9:1–10:1). Delivers strongest power from 3200–3700 rpm. Kit includes camshafts and installation components. Installer must verify clearances; requires high lift valve springs.

€365.33 €459.27

HP+® Camchest Kit — Chain drive, Intake & Exhaust, FEULING PARTS 7201

-€420.76

FEULING OIL PUMP CORP. HP+® Camchest Kit — Chain drive, Intake & Exhaust, FEULING...

Complete camchest kit for '99-'06 Twin Cam (except '06 Dyna). Improves oil pressure, lowers temps, and includes pump, camshafts, lifters and all hardware.

€1,636.28 €2,057.04

-€420.76

FEULING OIL PUMP CORP. HP+® Camchest Kit — Chain Drive, 574 Series

Complete camchest replacement kit for '99-'06 Twin Cam (except '06 Dyna). Restores reliability, increases oil pressure and flow, reduces engine and oil temperatures, and includes all necessary components for installation.

€1,636.28 €2,057.04

-€10.86

ANDREWS Cam Drive Gear — 2.7324" diameter, undersize -0.003"

High-quality heat-treated cam drive component, made in the U.S.A.; recommended for professional installation.

€42.24 €53.10

-€51.96
Out of Stock

ANDREWS C Grind Cam — Gear, Duration 278°, Lift 0.525"/0.550"

More mid-range and top-end power for street and drag bikes; works with solid or hydraulic lifters. Made in the USA.

€202.08 €254.04

-€53.08

ANDREWS N Grind Cam — Intake 234°, Exhaust 240°, Lift 0.348"

Stock Knuckle replacement cam for stock motors and classic engine restoration. Made in the U.S.A.

€206.42 €259.50

-€54.82

ANDREWS S Grind Cam — S grind, 262° duration

Bolt-in performance cam with a smooth idle and a strong pull to 6000 rpm. Made in the U.S.A.

€213.22 €268.04

Contact us

Products

Our company